donkeydaisy0

How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners have a unique set of steps to add an additional key. saab key programming near me requires dealer support using a handheld computer dubbed Tech-2. Then a new key and transponder are required to be purchased and programmed to the car. Change your keys regularly to prevent one from wearing out quicker than the other. This will help keep your keys in pristine condition. Replacement Case The new key fobs are not like the older Saab keys. They are equipped with electronics that make it difficult to duplicate. This has made car theft much more difficult than it was just a few years ago. It also makes it more expensive to replace lost keys. Saab 9-3 owners must have two working keys. If one is lost it costs a fortune to purchase a new one for the car since it requires replacing the CIM module and re-programming the locking cylinders. Dealers usually charge between $100 and $200 to do this. There are ways to cut down on these high costs. Some parts retailers will look up the code from an old key (usually the same one that opens the doors and turns the ignition) and cut a brand new metal key blade for only a fraction of the dealer's cost. The key must, however, be identical to the original in order to function within your car. You can also change the case yourself by following these steps. You'll need a flathead screwdriver and some patience. With the screwdriver, pry apart the plastic, and then take off the emergency key. When the case is opened remove all electronics and put them back in the new case. Make sure to insert the correct badge and key back into the case as well. Replacement Battery The replacement battery for the Saab 9-3 is an inexpensive part that can be replaced quickly and easily. This video tutorial on DIY from YouTube user Cyclone Cyd explains how to replace the remote key fob battery in just four steps. This tutorial is compatible with any modern Saab key fob. However, the process could differ slightly. The first step is to find the button that lets off the backup key inside the fob. This is usually located close to the Saab logo on the back of the fob. Next, use the flathead screwdriver to insert into the small hole of this button. This should be enough to allow you to open the fob case so that you can replace the battery. Once you have installed the new CR1632 batteries, you can put back together the remote key fob. You can then program it into your car. The entire process should take no more than an hour or less. This is a simple procedure that doesn't require special tools. If you lose a key, the process is a bit more involved, but it can still be completed. The dealer will need to verify the VIN of the car, and then order a replacement key blade and a TWICE module with the proper unique code. After that, they'll have to cut the replacement key and then program it with a new software tool called MDI. Replacement Key Fob The key fob is the device that locks and unlocks your car. It has an internal battery. They have a limited life span and eventually die. It is a common problem in all vehicles. The good news is you can replace the battery in most key fobs, without having to replace the entire case. You can buy fobs replacements on Amazon that have all the electronics already in place, so you'll just pop open the case and replace those batteries that are old. It is important to remember that you'll have to take out the emergency key first. you can do this by inserting a small flathead screwdriver into the slot located in the middle of the case. The case should split when you work the screwdriver all around it. If you're ready to change your keys, keep an extra set on hand. This will save you lots of money. If you have a spare, you can have the dealer cut an additional key and program it to your car, which is much cheaper than replacing the entire key fob. If you don't have a spare you can add a second key to your car, but this will require a lot of research and effort. Adding a second key costs about a few hundred dollars and also requires programming of the car's computer. Professionals can do this however, it's a costly option. Replacement Ignition The latest SAAB 9-3 has an advanced alarm system based on a key code. This means that if you lose your only functioning key, getting another one could be very expensive as the car has to have a computer module installed and it must also be designed to accept a different key. Dealers can even charge hundreds of dollars to program an additional key when they are not able to do it. If you've lost the only working key the dealer will replace the computer in your car (known as the CIM or SAAB TWICE) in order to make a replacement, and will charge you the highest price for it. We can reprogramme the existing EEPROM on your car's computer so that it is prepared for a new key. This will save you more than 50% of the price you'd pay an auto dealer. If you've been a long-time owner of an 03-11 SAAB 9-3, you likely have noticed that the ignition switch isn't all that durable. If your ignition key isn't functioning properly, you must look into replacing it. They can become extremely sticky and the buttons have been known to fall off. Luckily, replacing the ignition key isn't as complicated as it sounds and can be done quickly using the appropriate tools.